View SGM811_8987251.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

sgm 811 / sgm812 microprocessor supervisory with manual reset input g eneral d escription the sgm 811/ sgm 812 supervisory circuits monitor the power supply voltage in microprocessor and digital systems. the sgm 811 / sgm 812 is designed to monitor seven differen t voltages; t hese voltages have been selected for the effective monitoring of 1.8 v, 2.5v, 3v, 3.3v and 5 v supply voltage levels. they provide a reset output during power - up, power - down and brownout conditions. on power - up, an internal timer holds reset asserted for 240ms. this holds the microprocessor in a reset state until conditions have stabilized. the reset output remains operational with v cc as low as 1v. the sgm 811 provides an active low reset signal ( reset ) while the sgm 81 2 provides an active high signal (reset) output. the sgm 811/ sgm 812 has a manual reset input. the manual reset function is very useful, especially if the circuit in which the sgm 811/ sgm 812 is operating enters into a state that can only be detected by the user. allowing the user to reset a system manually can reduce the damage or danger that could otherwise be caused by an out - of - control or locked system. the devices come in sot - 143 and sot - 23 -5 package s. applications microprocessor systems contr ollers intelligent instruments automotive systems safety systems portable instruments features superior upgrade for max811/max812 and adm811/adm812 specified o ver temperature low power consumption ( 13 a t yp ) precision voltage monitor: 1.8 v, 2.5v, 3v, 3.3v and 5 v options reset assertion down to 1 v v cc 150 ms min power - on reset logic low reset output ( sgm 811) logic high reset output ( sgm 812) manual reset input green sot - 143 and sot -23-5 package s pin configurations ( top view ) 1 3 4 sot -23-5 gnd v cc reset / reset 5 mr 2 nc 1 2 3 4 sot -143 gnd v cc reset / reset mr typical operation ci rcuit microprocessor system sgm 811 gnd reset mr reset gnd v cc v cc 100k rev. b . 4 sg micro corp www.sg - micro.com a ll data sheet.com
microprocessor supervisory with manual reset input sgm 811/812 package/ordering information ordering number reset threshold (v) peckage type specified temperature range package marking pack ing option SGM811 - lx n5 /tr 4.63 sot -23 -5 -40 to +125 811l tape and reel, 3000 SGM811 -m xn5 /tr 4.38 sot -23 -5 -40 to +125 811m tape and reel, 3000 SGM811 - jxn5/tr 4.00 sot -23 -5 -40 to +125 811j tape and reel, 3000 SGM811 - txn5/tr 3.08 sot -23 -5 -40 to +125 811t tape and reel, 3000 SGM811 -sxn5/tr 2.93 sot -23 -5 -40 to +125 811s tape and reel, 3000 SGM811 - rxn5/tr 2.63 sot -23 -5 -40 to +125 811r tape and reel, 3000 SGM811 - zxn5/tr 2.32 sot -23 -5 -40 to +125 811z tape and reel, 3000 SGM811 - lxka4/tr 4.63 sot -143 -40 to +125 811l tape and reel, 3000 SGM811 - mxka4/tr 4.38 sot -143 -40 to +125 811m tape and reel, 3000 SGM811 - jxka4/tr 4.00 sot -143 -40 to +125 811j tape and reel, 3000 SGM811 - txka4/ tr 3.08 sot -143 -40 to +125 811t tape and reel, 3000 SGM811 -sxka4/tr 2.93 sot -143 -40 to +125 811s tape and reel, 3000 SGM811 - rxka4/tr 2.63 sot -143 -40 to +125 811r tape and reel, 3000 SGM811 - zxka4/tr 2.32 sot -143 -40 to +125 811z tape and reel, 3000 SGM811 -xxka4 /tr 1.63 sot -143 -40 to +125 811x tape and reel, 3000 sgm812 - lxn5/tr 4.63 sot -23 -5 -40 to +125 812l tape and reel, 3000 sgm812 -m xn5/tr 4.38 sot -23 -5 -40 to +125 812m tape and reel, 3000 sgm812 - jxn5/tr 4.00 sot -23 -5 -40 to +125 812j tape and reel, 3000 sgm812 - txn5/tr 3.08 sot -23 -5 -40 to +125 812t tape and reel, 3000 sgm812 -sxn5/tr 2.93 sot -23 -5 -40 to +125 812s tape and reel, 3000 sgm812 - rxn5/tr 2.63 sot -23 -5 -40 to +125 812r tape and reel, 3000 sgm812 - zxn5/tr 2.32 s ot -23 -5 -40 to +125 812z tape and reel, 3000 sgm812 - lxka4/tr 4.63 sot -143 - 40 to +125 812l tape and reel, 3000 sgm812 - mxka4/tr 4.38 sot -143 -40 to +125 812m tape and reel, 3000 sgm812 - jxka4/tr 4.00 sot -143 -40 to +125 812j tape and reel, 3000 s gm812- txka4/tr 3.08 sot -143 -40 to +125 812t tape and reel, 3000 sgm812 -sxka4/tr 2.93 sot -143 -40 to +125 812s tape and reel, 3000 sgm812 - rxka4/tr 2.63 sot -143 -40 to +125 812r tape and reel, 3000 sgm812 - zxka4/tr 2.32 sot -143 -40 to +125 812z ta pe and reel, 3000 2 sg micro corp www.sg - micro.com a ll data sheet.com
microprocessor supervisory with manual reset input sgm 811/812 electrical characteristics (v cc typ = 5v for l/m/j models, 3.3v for t/s models, 3v for r models, 2.5v for z models, 1.8v for x models; unless otherwise noted.) parameter conditions min typ max units supply voltage t a = 0 to + 70 1.0 5.5 v t a = - 40 to +125 1.2 5.5 v current v cc < 5.5 v, sgm 81 _l/m/j, t a = + 25 17 30 a v cc < 5.5 v, sgm 81 _l/m/j, t a = - 40 to +125 50 a v cc < 3.6 v, sgm 81 _r/s/t /z/x , t a = + 25 13 25 a v cc < 3.6 v, sgm 8 1 _r/s/t /z /x , t a = - 40 to + 125 45 a reset voltage threshold sgm 81 _l t a = + 25 4.537 4.63 4.723 v t a = - 40 to +125 4.40 4.86 v sgm 81 _m t a = + 25 4.292 4.38 4.468 v t a = - 40 to +125 4.16 4.56 v sgm 81 _j t a = + 25 3.92 4.00 4.08 v t a = - 40 to +125 3.8 4.2 v sgm 81 _t t a = + 25 3.003 3.08 3.157 v t a = - 40 to +125 2.92 3.23 v sgm 81 _s t a = + 25 2.857 2.93 3.0 0 3 v t a = - 40 to +125 2.78 3.08 v sgm 81 _r t a = + 25 2.564 2.63 2.696 v t a = - 40 to +125 2.50 2.76 v sgm81_z t a = + 25 2.262 2.32 2.378 v t a = - 40 t o +125 2.22 2.42 v SGM811x t a = +25 1.589 1.63 1.671 v t a = - 40 to +125 1.55 1.71 v reset threshold temperature coefficient 30 ppm/ c v cc to reset/ reset delay v cc = v th to (v th - 100mv) 20 s reset active timeout period t a = - 40 to +85 150 240 560 ms t a = - 40 to +125 100 840 ms manual reset minimum pulse w idth 10 s glitch immunity 100 ns reset/ reset propagation delay 0.5 s pull - up resistance 1 m the manual reset circuit will ac t on: an input rising above v cc > v th(max) , sgm81_l/m/j 2.3 v an input falling below v cc > v th(max) , sgm81_l/m/j 0.8 v an input rising above v cc > v th(max) , sgm81_r/s/t/z /x 0.7 v cc v an input falling below v cc > v th(max) , sgm81_r/s/t/z /x 0. 25 v cc v 3 sg micro corp www.sg - micro.com a ll data sheet.com
microprocessor supervisory with manual reset input sgm 811/812 electrical characteristics (v cc typ = 5v for l/m/j models, 3.3v for t/s models, 3v for r models, 2.5v for z models, 1.8v for x models; unless otherwise noted.) parameter conditions min typ max units reset/ reset output volta ge low (SGM811r/s/t/z /x ) v cc = v th(min) , i sink = 1.2ma 0.3 v low (SGM811l/m/j) v cc = v th(min) , i sink = 3.2ma 0.4 v low (SGM811r/s/t/z /x/l/m/j) v cc > 1.0 v, i sink = 50a 0.3 v high (SGM811r/s/t/z /x ) v cc > v th(max) , i source = 500a 0.8 v cc v hi gh (SGM811l/m/j) v cc > v th(max) , i source = 800a v cc - 1.5 v low (sgm812r/s/t/z /x ) v cc = v th(max) , i sink = 1.2ma 0.3 v low (sgm812l/m/j) v cc = v th(max) , i sink = 3.2ma 0.4 v high (sgm812 r/s/t/z/ x/ l/m/j) 1.8 v < v cc < v th(min) , i source = 150a 0.8 v cc v 4 sg micro corp www.sg - micro.com a ll data sheet.com
microprocessor supervisory with manual reset input sgm 811/812 absolute maximum ratings (typical values are at t a = + 25c, unless otherwise noted.) terminal voltage (with respect to ground) v cc ................................................................. . ........... - 0.3v to 6v all other inputs .......................................... ...- 0.3 v to v cc + 0.3 v input current v cc , mr ....................................................................... . ..... 20 ma output current reset , reset .................................................. . .............. 20ma power dissipation, p d @ t a = + 25 sot -23 -5. ....................................... . ....................................0.4w sot -143 ........................................................................... 0.32 w o perating temperature range ......................... -40 to +125 junction temperature...................... . ................................ 150 storage temperature........ .......................... . .....-65 to +150 lead temperature ( s oldering, 10s) ................................... 260 esd susceptibility hbm..................................................................................4000v mm......................................................................................400v stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. these are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operation al sections of the specifications is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. caution this integrated circuit can be damaged by esd if you dont pay attention to esd protection. sgmicro recommends that all int egrated circuits be handled with appropriate precautions. failure to observe proper handling and installation procedures can cause damage. esd damage can range from subtle performance degradation to complete device failure. precision integrated circuits ma y be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. sgmicro reserves the right to make any change in circuit design, specification or other related things if necessary without notice at any time. p lease contact sgmicro sales office to get the la test datasheet. pin description name pin number function SGM811 sgm812 sot - 143 sot - 23 - 5 sot - 143 sot - 23 - 5 gnd 1 1 1 1 ground nc 2 2 no c onnect. reset 2 3 active low logic output. reset remains low while v cc is below the reset threshold or when mr is low; reset then remains low for at least 1 5 0ms after v cc rises above the reset threshold. reset 2 3 active high logic output. reset remains high while v cc is below the reset threshold or when mr is low; reset then remains high for 240ms (typical) after v cc rises above the reset threshold. mr 3 4 3 4 manual reset. this active low debounced input will ignore input pulses of 100ns or less (typical) and is guaranteed to accept input pulses of greater than 10 s. leave floating when not used. v cc 4 5 4 5 power supply voltage that is monitored. 5 sg micro corp www.sg - micro.com a ll data sheet.com
microprocessor supervisory with manual reset input sgm 811/812 typical performance characteristics power-down reset delay vs. temperature 0 50 100 150 200 250 -50 -30 -10 10 30 50 70 90 110 130 temperature ( ) power-down reset (s) SGM811l/m/j v od = v th - v cc v od = 10mv v od = 20mv v od = 100mv v od = 200mv power-down reset delay vs. temperature 0 50 100 150 200 250 300 -50 -30 -10 10 30 50 70 90 110 130 temperature ( ) power-down reset (s) SGM811t/s/r v od = v th - v cc v od = 10mv v od = 20mv v od = 100mv v od = 200mv power-up reset delay vs. temperature 220 225 230 235 240 245 250 255 260 265 270 -50 -30 -10 10 30 50 70 90 110 130 temperature ( ) power-down reset (ms) sgm8_s supply current vs. temperature (no load) 0 5 10 15 20 25 30 -50 -30 -10 10 30 50 70 90 110 130 temperature ( ) supply current (a) v cc = 5.5v v cc = 3.6v normalized reset voltage threshold vs. temperature 0.988 0.99 0.992 0.994 0.996 0.998 1 1.002 1.004 1.006 1.008 -50 -30 -10 10 30 50 70 90 110 130 temperature ( ) normalized reset threshold 0 50 100 150 200 250 300 350 400 1 10 100 1000 maximum transient duration (s) SGM811l/m/j SGM811t/s/r maximum transient duration without causing a reset pulse vs. reset comparator overdrive reset comparator overdrive, v th - v cc (mv) 6 sg micro corp www.sg - micro.com a ll data sheet.com
microprocessor supervisory with manual reset input sgm 811/812 typical performance characteristics reset output voltage vs. supply voltage 200ms/div 2v/div supply voltage reset output 5v p-p voltage SGM811s SGM811r 7 sg micro corp www.sg - micro.com a ll data sheet.com
microprocessor supervisory with manual reset input sgm 811/812 application information manual reset the SGM811/sgm812 is equipped with a manual reset input this input is designed to operate in a noisy environment where unwanted glitches could be induced. these glitches could be produced by the bounc ing action of a switch contact, or where a manual reset switch may be located some distance away from the circuit (the cabling of which may pick - up noise). the manual reset input is guaranteed to ignore logically valid inputs that are faster than 100 ns and to accept inputs longer in duration than 10s. very accurate reset threshold because the SGM811/sgm812 can operate effectively even when there are large degradations of the supply voltages, the possibility of a malfunction during a power failure is grea tly reduced. another advantage of the SGM811/sgm812 is its very accurate internal voltage reference circuit. combined, these benefits produce an exceptionally reliable microprocessor supervisory circuit. sgm 811 gnd reset v cc v cc figure 1 . ensuring a valid reset output down to v cc = 0v ensuring a valid reset output down to v cc = 0 v when v cc falls below 1.0 v, the SGM811/sgm812s reset no longer sinks current. therefore, a high impedance cmos logic input connected to reset may drift to undetermined logic levels. to eliminate this problem, a 100 k resistor should be connected fr om reset to ground. reset output on power - up and after v cc rises above the reset threshold, an internal timer holds the reset output active for 240 ms (typical). this is intended as a power - on reset signal for the processor. it allows time for both the power supply and the microprocessor to stabilize after power - up. if a power supply brownout or interruption occurs, the reset output is similarly activated and remains active for 240 ms (typical) after the supply recovers. this allows time f or the power supply and microprocessor to stabilize. the SGM811 provides an active low reset output ( reset ) while the sgm812 provides an active high output ( reset ). during power - down of the SGM811, the reset output remains valid (low) with v cc as low as 1v. this ensures that the microprocessor is held in a stable shutdown condition as the supply falls and also ensures that no spurious activity can occur via the microprocessor as it powers up. glitch immu nity the SGM811/sgm812 contains internal filtering circuitry providing glitch immunity from fast transient glitches on the power supply line. t 1 t 1 reset v cc v ref v ref v ref v ref t 1 = reset time = 240ms typical v ref = reset voltage threshold figure 2 . power fail reset timing interfacing t o other devices output the SGM811/sgm812 is designed to integrate with as many devices as possible. one feature of the SGM811/sgm812 is the reset output, which is directly proportional to v cc (this is guaranteed only while v cc is greater than 1v). this enables the part to be used with both 3v and 5 v, or any nominal voltage within the minimum and maximum specifications for v cc . 8 sg micro corp www.sg - micro.com a ll data sheet.com
microprocessor supervisory with manual reset input sgm 811/812 package outline dimensions sot- 23 -5 e e1 e e1 b d a1 a2 a c l 0.2 recommended land pattern (unit: mm) 1.90 2.59 0.99 0.69 0.95 symbol dimensions in millimeters dimensions in inches min max min max a 1.050 1.250 0.041 0.049 a1 0.000 0.100 0.000 0.004 a2 1.050 1.150 0.041 0.045 b 0.300 0.500 0.012 0.020 c 0.100 0.200 0.004 0.008 d 2.820 3.020 0.111 0.119 e 1.500 1.700 0.059 0.067 e1 2.650 2.950 0.104 0.116 e 0.950 bsc 0.037 bsc e1 1.90 0 bsc 0.075 bsc l 0.300 0.600 0.012 0.024 0 8 0 8 9 sg micro corp www.sg - micro.com a ll data sheet.com
microprocessor supervisory with manual reset input sgm 811/812 p ackage outline dimensions sot- 143 e b b1 d d e1 e1 e a a2 a1 l 0.250 c l1 recommended land pattern (unit: mm) 0.95 1.90 0.55 1.0 0.20 2.2 0.95 symbol dimensions in millimeters dimensions in inches min max min max a 0.900 1.150 0.035 0.045 a1 0.000 0.100 0.000 0.004 a2 0.900 1.050 0.035 0.041 b 0.300 0.500 0.012 0.020 b1 0.750 0.900 0.030 0.035 c 0. 080 0.150 0.003 0.006 d 2.8 0 0 3.000 0.110 0.118 d 0.200 typ 0.008 typ e 1. 2 00 1. 4 00 0.047 0.055 e1 2.250 2.550 0.089 0.100 e 0.95 typ 0.037 typ e1 1.800 2.000 0.071 0.079 l 0. 55 ref 0.022 ref l1 0.300 0.500 0.012 0.020 0 8 0 8 10 sg micro corp www.sg - micro.com a ll data sheet.com
microprocessor supervisory with manual reset input sgm 811/812 tape and r eel information note: the picture is only for reference. please make the object as the standard. key parameter list of tape and reel package type reel diameter reel width w1 (mm) a0 (mm) b0 (mm) k0 (mm) p0 (mm) p1 (mm) p2 (mm) w (mm) pin1 quadrant sot -23 -5 7 9.5 3. 2 3.2 1. 4 4.0 4.0 2.0 8.0 q3 sot -143 7 9.5 3. 2 2.8 1.3 4.0 4.0 2.0 8.0 q3 reel width (w1) reel diameter reel dimensions tape dimensions direction of feed p2 p0 w p1 a0 k0 b0 q1 q2 q4 q3 q3 q4 q2 q1 q3 q4 q2 q1 11 sg micro corp www.sg - micro.com a ll data sheet.com
microprocessor supervisory with manual reset input sgm 811/812 carton box dimensions note: the picture is only for reference. please make the object as the standard. key p arameter list of carton box reel type length (mm) width (mm) height (mm) pizza/carton 7 (option) 368 227 224 8 7 44 2 410 224 18 12 sg micro corp www.sg - micro.com a ll data sheet.com

▲Up To Search▲

Price & Availability of SGM811

	To Download SGM811 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .